Open a DOS Command Prompt (in Windows NT® 4.0, 2000, or XP, click Start, Run, then type CMD and press OK, or in Windows 9x click Start, Programs, Accessories, and then A COMMUNICATION OR CRITICAL FIRMWARE ERROR If you need to download a upgraded version of firmware go here CLICK HERE and then click on the H.P. Action Remove any jammed media from the paper path. Maybe its slipping past checks because the harware is altering signals during transit. his comment is here
You can replace these but it takes awhile just replace the whole assembly if not. 49.xxxx errors = upgrade firmware , possible driver, cable or corrupt print job or program Also Action Press Cancel Job to clear the print job from the printer memory. For best results, use the HP driver that came with the printer. (See the printer user guide for information about printer drivers.) Press (Select) to clear the error message. (The job CAUTION: Do not use a sharp object to clear paper from the fuser area. http://www.copytechnet.com/forums/hp/93289-hp-4250-error-49-235f.html
I was waiting to get a certain programmer that supports parallel flash components. Every situation is different and this thread will never end until the 4250 is dead :) by akuma6099 on Jan 24, 2012 at 4:48pm Add comment Please sign in to comment If that is the case you will have to deal with both hp and novell and I am sure each will blame the other and the only way around it will
CAUTION: Do not fan the paper. The Printer Works trusts its customers and does not charge for cores upfront.http://www2.printerworks.com/cgi-win/tpwall.exe/find?Q3653-67901Advertising1Advertising AdvertisingAdvertise hereRelated searcheserrorerror 1error checkingerror codeerror code generatorerror exampleserror loadingerror occurred Our servicesDirectory categoriesAdd a websiteLatest searchesPopular searchesWe Thank you! Hp Laserjet 4250n 49.4c02 Service Error by Anonymous on Oct 31, 2007 at 1:54pm Add comment Please sign in to comment 0 I too am having trouble with this error on a new printer.
Once the printer is back online, print a Configuration Page and verify that the new firmware has been installed. Hp Laserjet 4200 Error Codes by unknown on Jan 24, 2012 at 9:37pm Add comment Please sign in to comment 0 I have the 4250dtn in my office. Figure 35: Removing the optional duplexer, if installed Open the rear output bin and pull the extension outward until it stops. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpl12422 alternates with 68.X PERMANENT STORAGE FULL To continue press (Select) 68.X PERMANENT STORAGE WRITE FAIL To continue press (Select) 69.X PRINTER ERROR To continue turn off then on 79.XXXX PRINTER ERROR
Once you get that clear, update firmware and drivers. Hp Laserjet 4200 Cartridge Installed Message Most discussion I've read refers to HP4250 I've noticed. Turn the device off and then on.3. ERROR - Specified backup location could not be found.
Remove the rear output bin by pushing the left side of the bin to the right and then removing the hinge pin from the slot in the chassis of the printer. http://www.fixyourownprinter.com/posts/39866 Unplug the power cord for 10 seconds. Hp Laserjet 4250 Error Codes This NAND holds the firmware or printer OS. 49.ff04 Service Error Close the door.
The ON setting determines that the clearable warning message appears until (Select) is pressed. this content Look for the jam in another location, contact HP, or contact an authorized service provider. But we just had a core upgrade to the Nexus 5548up and that seemed to help the issue as well.Hope the port settings help. Hot water sets the toner into the fabric. Hp Printer Error Codes List
Remove all memory DIMMs or third party DIMMs from the printer. 6. Verify that the ribbon cables are fully seated in the connectors on the D.C. Figure 8: Sliding the tray out If the edge of the jammed paper is visible in the feed area, slowly pull the paper down and out of the printer. (Do not weblink For enterprise products go to Hewlett Packard Enterprise.© Copyright 2016 HP Development Company, L.P.
If the error message disappears, reinstall each DIMM, flash memory card, and EIO device individually, make sure to turn the MFP power off and then on again as you install each Hp Laserjet 4200 And 4300 Series Printers Drivers Print a Configuration page and verify that the tray settings match the media in the tray. Make sure your connections to the PC are good from either end.
These messages are not affected by the AUTO CONTINUE setting. To effectively clear 49 errors, the print queue must be cleared. Make the page contents less complex and resend the print job. 13.98 Paper Jam The stapler/stacker LED blinks in amber.
top 68.X PERMANENT STORAGE ERROR For help press ? This causes static electricity, which can cause paper jams. Try printing a job from a different software application. 4. check over here Same problem as RAM.
A 49 error is a firmware error and has many causes from applications, ... I've tried the powering off without the memory, didn't work. top 59.4 EP MOTOR ROTATION ERROR (HP LaserJet 4300 only) Description The print-cartridge drive motor (HP LaserJet 4300 only) is not functioning properly. Finish it up and see if you have the same issue.
Turn printer off then on.4. Powered by vBulletin Version 4.2.2 Copyright © 2016 vBulletin Solutions, Inc. If the job prints, go back to the first program and try printing a different file. by unknown on May 3, 2012 at 3:46pm Add comment Please sign in to comment 0 Hi,I'm getting the same error on a HP P3015, which already has the latest firmware
If tape has been removed, replace the toner cartridge. All rights reserved. This should ...